Skip to content

AVD example for a dual data center using L3LS

Introduction

This example is meant to be used as the logical evolution in AVD to new users. Therefore, this document follows the single data center structure and assumes the reader could deploy the scenario described in the AVD example for a single data center using L3LS.

The main goal of this example is to provide a base scenario to enable the new users to grow in the number of DCs (Data Centers) and configure the interconnection between different DCs.

The example includes and describes all the AVD files and their content used to build an L3LS EVPN/VXLAN Symmetric IRB network covering two twin DCs. This design will use the EVPN DC GW feature to avoid unnecessary BGP overlay convergence. This feature rewrites EVPN routes on a set of devices (called EVPN Gateways) and shows the Gateways as the next hop for advertisements outside the EVPN domain using a DCI (DC Interconnect).

DC1

  • Two (virtual) spine switches.
  • Two sets of (virtual) leaf switches, serving endpoints such as servers.
  • Two (virtual) layer2-only switches often used for server management connectivity.

DC2

  • Two (virtual) spine switches.
  • Two sets of (virtual) leaf switches, serving endpoints such as servers.
  • Two (virtual) layer2-only switches often used for server management connectivity.

To follow the network design principle using patterns, both DCs have the same layout to keep a repetitive pattern using the Leaf and Spine architecture.

However, there is no hard requirement to have the same number of devices. For example, one DC could use two spines while the other could use four spines to comply with redundancy and bandwidth requirements.

Integration with CloudVision is not included in this example to keep everything as simple as possible. In this case, the Ansible host will communicate directly with the switches using eAPI. There are two playbooks included in this example to show the following:

  • Building the intended configuration and documentation
  • Deploying the configuration directly to the switches using eAPI

Installation

Requirements to use this example:

  • Follow the installation guide for AVD found here.
  • Run the following playbook to copy the AVD examples to your current working directory, for example ansible-avd-examples:

ansible-playbook arista.avd.install_examples

This will show the following:

 ~/ansible-avd-examples# ansible-playbook arista.avd.install_examples

PLAY [Install Examples]***************************************************************************************************************************************************************************************************************************************************************

TASK [Copy all examples to ~/ansible-avd-examples]*****************************************************************************************************************************************************
changed: [localhost]

PLAY RECAP
****************************************************************************************************************************************************************************************************************************************************************************
localhost                  : ok=1    changed=1    unreachable=0    failed=0    skipped=0    rescued=0    ignored=0

After the playbook has run successfully, the directory structure will look as shown below, the contents of which will be covered in later sections:

ansible-avd-examples/ (or wherever the playbook was run)
  |── dual-dc-l3ls
    ├── ansible.cfg
    ├── documentation
    ├── group_vars
    ├── images
    ├── intended
    ├── inventory.yml
    ├── build.yml
    ├── deploy.yml
    ├── README.md
    └── switch-basic-configurations

Info

If the content of any file is modified and the playbook is rerun, the file will not be overwritten. However, if any file in the example is deleted and the playbook is rerun, Ansible will re-create the file.

Overall design overview

Physical topology

The drawing below shows the physical topology used in this example. The interface assignment is identical to the single DC example. The only change introduced in this topology is the DCI links, which are connected to port Ethernet 6 in dc1-leaf2a/b to dc2-leaf2a/b:

Figure: Arista Leaf Spine physical topology

IP ranges used

Out-of-band management IP allocation for DC1 172.16.1.0/24
Default gateway 172.16.1.1
dc1-spine1 172.16.1.11
dc1-spine2 172.16.1.12
dc1-leaf1a 172.16.1.101
dc1-leaf1b 172.16.1.102
dc1-leaf2a 172.16.1.103
dc1-leaf2b 172.16.1.104
dc1-leaf1c 172.16.1.151
dc1-leaf2c 172.16.1.152
dc2-spine1 172.16.1.21
dc2-spine2 172.16.1.22
dc2-leaf1a 172.16.1.111
dc2-leaf1b 172.16.1.112
dc2-leaf2a 172.16.1.113
dc2-leaf2b 172.16.1.114
dc2-leaf1c 172.16.1.161
dc2-leaf2c 172.16.1.162
Point-to-point links between leaf and spine (Underlay)
DC1 10.255.255.0/26
DC2 10.255.255.64/26
Loopback0 interfaces used for EVPN peering
DC1 10.255.0.0/27
DC2 10.255.128.0/27
Loopback1 interfaces used for VTEP (Leaf switches)
DC1 10.255.1.0/27
DC2 10.255.129.0/27
VTEP Loopbacks used for diagnostics (Leaf switches)
VRF10 - Common for both DCs 10.255.10.0/27
VRF11 - Common for both DCs 10.255.11.0/27
SVIs (interface vlan…) 10.10.<VLAN-ID>.0/24
For example interface VLAN11 has the IP address: 10.10.11.1
MLAG Peer-link (interface vlan 4094) (Leaf switches)
DC1 10.255.1.64/27
DC2 10.255.129.64/27
MLAG iBGP Peering (interface vlan 4093) (Leaf switches)
DC1 10.255.1.96/27
DC2 10.255.129.96/27

BGP design

New BGP connections are established from dc1-leaf2a and dc1-leaf2b to dc2-leaf2a and dc2-leaf2b respectively. In addition, all BGP learned routes are redistributed into the underlay. This allows for easier troubleshooting, as all router IDs (Loopback0 IP addresses) and VTEPs (Loopback1 IP addresses) are reachable at a fabric level.

From the overlay perspective, each new leaf sees its peer in the twin DC as a new Route Server and will advertise all EVPN learned routes as they were directly connected to itself, making all changes inside its DC transparent to the twin DC.

Figure: Arista Underlay BGP Design

Figure: Arista Overlay BGP Design

Basic EOS config

As discussed in the single DC example, basic connectivity between the Ansible host and the switches must be established before Ansible can be used to push configurations. Remember, you must configure the following on all switches:

  • A hostname configured purely for ease of understanding.
  • An IP enabled interface - in this example, the dedicated out-of-band management interface is used.
  • A username and password with the proper access privileges.

Note

The folder dual-dc-l3ls/switch-basic-configurations/ contains a file per device for the initial configurations.

Ansible inventory, group vars, and naming scheme

The following drawing shows a graphic overview of the Ansible inventory, group variables, and naming scheme used in this example:

Figure: Ansible inventory and vars

Note

The two servers on DC1 (dc1-leaf1-server1 and dc1-leaf2-server1) and the two servers on DC2 (dc2-leaf1-server1 and dc2-leaf2-server1) at the bottom are not configured by AVD, but the switch ports used to connect to the servers are. For this reason, the diagram shows them outside of the FABRIC definition.

The same pattern used in the single DC example is followed:

  • Group names use uppercase and underscore
  • All hostnames use lowercase and dashes

The drawing also shows the relationships between groups and their children. Be aware that all declarations on a higher level are inherited by children automatically.

Content of the inventory.yml file

This section describes the entire ansible-avd-examples/dual-dc-l3ls/inventory.yml file used to represent the above topology.

In this example, we will consider that no DNS is available and define the IPs the Ansible host has to reach per device.

---
# inventory.yml
all:
  children:
    FABRIC:
      children:
        DC1:
          children:
            DC1_SPINES:
              hosts:
                dc1-spine1:
                  ansible_host: 172.16.1.11
                dc1-spine2:
                  ansible_host: 172.16.1.12
            DC1_L3_LEAVES:
              hosts:
                dc1-leaf1a:
                  ansible_host: 172.16.1.101
                dc1-leaf1b:
                  ansible_host: 172.16.1.102
                dc1-leaf2a:
                  ansible_host: 172.16.1.103
                dc1-leaf2b:
                  ansible_host: 172.16.1.104
            DC1_L2_LEAVES:
              hosts:
                dc1-leaf1c:
                  ansible_host: 172.16.1.151
                dc1-leaf2c:
                  ansible_host: 172.16.1.152
        DC2:
          children:
            DC2_SPINES:
              hosts:
                dc2-spine1:
                  ansible_host: 172.16.1.21
                dc2-spine2:
                  ansible_host: 172.16.1.22
            DC2_L3_LEAVES:
              hosts:
                dc2-leaf1a:
                  ansible_host: 172.16.1.111
                dc2-leaf1b:
                  ansible_host: 172.16.1.112
                dc2-leaf2a:
                  ansible_host: 172.16.1.113
                dc2-leaf2b:
                  ansible_host: 172.16.1.114
            DC2_L2_LEAVES:
              hosts:
                dc2-leaf1c:
                  ansible_host: 172.16.1.161
                dc2-leaf2c:
                  ansible_host: 172.16.1.162

    NETWORK_SERVICES:
      children:
        DC1_L3_LEAVES:
        DC1_L2_LEAVES:
        DC2_L3_LEAVES:
        DC2_L2_LEAVES:
    CONNECTED_ENDPOINTS:
      children:
        DC1_L3_LEAVES:
        DC1_L2_LEAVES:
        DC2_L3_LEAVES:
        DC2_L2_LEAVES:

Defining device types

As discussed in the single DC scenario, all device types must be explicitly defined. The device types are specified in the group variable files with the following names and content:

---
### group_vars/DC1_SPINES.yml

type: spine
---
### group_vars/DC1_L3_LEAVES.yml

type: l3leaf
---
### group_vars/DC1_L2_LEAVES.yml

type: l2leaf
---
### group_vars/DC2_SPINES.yml

type: spine
---
### group_vars/DC2_L3_LEAVES.yml

type: l3leaf
---
### group_vars/DC2_L2_LEAVES.yml

type: l2leaf

Setting fabric-wide configuration parameters

The ansible-avd-examples/dual-dc-l3ls/group_vars/FABRIC.yml file defines generic settings that apply to all children of the FABRIC group as specified in the inventory described earlier.

In this section, only additions to the previous example will be discussed. The only added change that must be inherited by both DCs is the L3 links between the L3 leaves, and it is represented at a fabric level using the following structure:

FABRIC.yml
    # L3 Edge port definitions. This can be any port in the entire Fabric, where IP interfaces are defined.
    l3_edge:
      # Define a new IP pool that will be used to assign IP addresses to L3 Edge interfaces.
      p2p_links_ip_pools:
        - name: DCI_IP_pool
          ipv4_pool: 172.100.100.0/24
      # Define a new link profile which will match the IP pool, the used ASNs and include the defined interface into underlay routing
      p2p_links_profiles:
        - name: DCI_profile
          ip_pool: DCI_IP_pool
          as: [65102, 65202]
          include_in_underlay_protocol: true
      # Define each P2P L3 link and link the nodes, the interfaces and the profile used.
      p2p_links:
        - id: 1
          nodes: [dc1-leaf2a, dc2-leaf2a]
          interfaces: [Ethernet6, Ethernet6]
          profile: DCI_profile
        - id: 2
          nodes: [dc1-leaf2b, dc2-leaf2b]
          interfaces: [Ethernet6, Ethernet6]
          profile: DCI_profile
  1. Define a new IP Pool named “DCI_IP_pool” using the prefix “172.100.100.0/24” to assign IP addresses.
  2. Define a new link profile called “DCI_profile” using the previously created IP pool. The ASN will be “65102” for left devices and “65202” for right devices. The interfaces will be included in the underlay routing protocol.
  3. Define a new link, with the left and right node hostname defined in AVD, along with the interface and finally assign a profile containing all required information to configure the link.

Setting device-specific configuration parameters

Both ansible-avd-examples/dual-dc-l3ls/group_vars/DC1.yml and ansible-avd-examples/dual-dc-l3ls/group_vars/DC2.yml files define settings that apply to all children of DC1 and DC2 groups as specified in the inventory described earlier.

In this section, we will discuss DC2 device definitions. From DC1, only the changes will be discussed, as definitions are the same as in the single DC L3LS example. The only change, the one used to include the EVPN DC GW, will be discussed later.

Creating the DC2.yml file limits the defined settings to DC2. In this example, DC2 follows the same configuration as DC1, but it could be different, keeping the DC1 definition intact while DC2 can be adjusted to meet other requirements.

DC2.yml
---
mgmt_gateway: 172.16.1.1 

spine:
  defaults:
    platform: vEOS-lab 
    loopback_ipv4_pool: 10.255.128.0/27 
    bgp_as: 65200 

  nodes: 
    - name: dc2-spine1
      id: 11 
      mgmt_ip: 172.16.1.21/24 

    - name: dc2-spine2
      id: 12
      mgmt_ip: 172.16.1.22/24

The following section covers the L3 leaf switches. Significantly more settings need to be set compared to the spine switches:

DC2.yml
l3leaf:
  defaults:
    platform: vEOS-lab 
    loopback_ipv4_pool: 10.255.128.0/27 
    loopback_ipv4_offset: 2 
    vtep_loopback_ipv4_pool: 10.255.129.0/27 
    uplink_switches: ['dc2-spine1', 'dc2-spine2'] 
    uplink_ipv4_pool: 10.255.255.64/26 
    mlag_peer_ipv4_pool: 10.255.129.64/27 
    mlag_peer_l3_ipv4_pool: 10.255.129.96/27 
    virtual_router_mac_address: 00:1c:73:00:00:99 
    spanning_tree_priority: 4096 
    spanning_tree_mode: mstp 

  node_groups: 
    - group: DC2_L3_LEAF1
      bgp_as: 65201 
      nodes:
        - name: dc2-leaf1a
          id: 1
          mgmt_ip: 172.16.1.111/24
          uplink_switch_interfaces:
            - Ethernet1
            - Ethernet1
        - name: dc2-leaf1b
          id: 2
          mgmt_ip: 172.16.1.112/24
          uplink_switch_interfaces:
            - Ethernet2
            - Ethernet2

    - group: DC2_L3_LEAF2
      bgp_as: 65202
      evpn_gateway: 
        evpn_l2:
          enabled: true
        evpn_l3:
          enabled: true
          inter_domain: true
      nodes:
        - name: dc2-leaf2a
          id: 3
          mgmt_ip: 172.16.1.113/24
          uplink_switch_interfaces:
            - Ethernet3
            - Ethernet3
          evpn_gateway:
            remote_peers: 
              - hostname: dc1-leaf2a
        - name: dc2-leaf2b
          id: 4
          mgmt_ip: 172.16.1.114/24
          uplink_switch_interfaces:
            - Ethernet4
            - Ethernet4
          evpn_gateway:
            remote_peers:
              - hostname: dc1-leaf2b

Since we are adding the EVPN DC GW functionality in DC2, we must also add it in DC1. This is a snipped part of ansible-avd-examples/dual-dc-l3ls/group_vars/DC1.yml file where the changes need to occur:

Important

The following is a snipped part of DC1.yml reflecting the changes needed compared to the single DC L3LS example. The goal is to configure EVPN DC GW functionality.

DC1.yml
        - group: DC1_L3_LEAF2
          bgp_as: 65102
          evpn_gateway:
            # Specific BGP EVPN Gateway functionality for route types 2 (MAC-IP), 3 (IMET) and 5 (IP-PREFIX) can be enabled separately as needed.
            evpn_l2:
              enabled: true
            evpn_l3:
              enabled: true
              inter_domain: true
          nodes:
            - name: dc1-leaf2a
              id: 3
              mgmt_ip: 172.16.1.103/24
              uplink_switch_interfaces:
                - Ethernet3
                - Ethernet3
              evpn_gateway:
                # Define remote peers of the EVPN VXLAN Gateway. If the hostname can be found in the inventory, ip_address and BGP ASN will be automatically populated. Manual override takes precedence. If the peer's hostname can not be found in the inventory, ip_address and bgp_as must be defined.
                remote_peers:
                  - hostname: dc2-leaf2a
            - name: dc1-leaf2b
              id: 4
              mgmt_ip: 172.16.1.104/24
              uplink_switch_interfaces:
                - Ethernet4
                - Ethernet4
              evpn_gateway:
                # Define remote peers of the EVPN VXLAN Gateway. If the hostname can be found in the inventory, ip_address and BGP ASN will be automatically populated. Manual override takes precedence. If the peer's hostname can not be found in the inventory, ip_address and bgp_as must be defined.
                remote_peers:
                  - hostname: dc2-leaf2b

Finally, the definition in DC2 for the L2 leaf switches:

DC2.yml
    # L2 Leaf switch group
    l2leaf:
      defaults:
        platform: vEOS-lab
        spanning_tree_mode: mstp

      node_groups:
        - group: DC2_L2_LEAF1
          uplink_switches: ['dc2-leaf1a', 'dc2-leaf1b']
          nodes:
            - name: dc2-leaf1c
              id: 11
              mgmt_ip: 172.16.1.161/24
              uplink_switch_interfaces:
                - Ethernet8
                - Ethernet8

        - group: DC2_L2_LEAF2
          uplink_switches: ['dc2-leaf2a', 'dc2-leaf2b']
          nodes:
            - name: dc2-leaf2c
              id: 12
              mgmt_ip: 172.16.1.162/24
              uplink_switch_interfaces:
                - Ethernet8
                - Ethernet8

Specifying network services (VRFs and VLANs) in the EVPN/VXLAN fabric

This file is identical to the one provided in the previous example. VRFs and VLANs are configured on all devices since no tags or filter are being used.

It is important to consider adding the new leaves to the Inventory as described in the Inventory section, so they will rely on this file to configure the network services.

NETWORK_SERVICES.yml
---
### group_vars/NETWORK_SERVICES.yml

tenants:
  # Definition of tenants. Additional level of abstraction to VRFs
  - name: TENANT1
    # Number used to generate the VNI of each VLAN by adding the VLAN number in this tenant.
    mac_vrf_vni_base: 10000
    vrfs:
      # VRF definitions inside the tenant.
      - name: VRF10
        # VRF VNI definition.
        vrf_vni: 10
        # Enable VTEP Network diagnostics
        # This will create a loopback with virtual source-nat enable to perform diagnostics from the switch.
        vtep_diagnostic:
          # Loopback interface number
          loopback: 10
          # Loopback ip range, a unique ip is derived from this ranged and assigned
          # to each l3 leaf based on it's unique id.
          loopback_ip_range: 10.255.10.0/27
        svis:
          # SVI definitions.
          - id: 11
            # SVI Description
            name: VRF10_VLAN11
            enabled: true
            # IP anycast gateway to be used in the SVI in every leaf.
            ip_address_virtual: 10.10.11.1/24
          - id: 12
            name: VRF10_VLAN12
            enabled: true
            ip_address_virtual: 10.10.12.1/24
      - name: VRF11
        vrf_vni: 11
        vtep_diagnostic:
          loopback: 11
          loopback_ip_range: 10.255.11.0/27
        svis:
          - id: 21
            name: VRF11_VLAN21
            enabled: true
            ip_address_virtual: 10.10.21.1/24
          - id: 22
            name: VRF11_VLAN22
            enabled: true
            ip_address_virtual: 10.10.22.1/24

    l2vlans:
      # These are pure L2 vlans. They do not have a SVI defined in the l3leafs and they will be bridged inside the VXLAN fabric
      - id: 3401
        name: L2_VLAN3401
      - id: 3402
        name: L2_VLAN3402

Specifying endpoint connectivity in the EVPN/VXLAN fabric

After the previous section, all VRFs and VLANs across the fabric are now defined on each leaf node. The ansible-avd-examples/dual-dc-l3ls/group_vars/CONNECTED_ENDPOINTS.yml file specifies the connectivity for all endpoints in the fabric (typically servers):

CONNECTED_ENDPOINTS.yml
---
### group_vars/CONNECTED_ENDPOINTS.yml

# Definition of connected endpoints in the fabric.
servers:
  # Name of the defined server.
  - name: dc1-leaf1-server1
    # Definition of adapters on the server.
    adapters:
      # Name of the server interfaces that will be used in the description of each interface
      - endpoint_ports: [ PCI1, PCI2 ]
        # Device ports where the server ports are connected.
        switch_ports: [ Ethernet5, Ethernet5 ]
        # Device names where the server ports are connected.
        switches: [ dc1-leaf1a, dc1-leaf1b ]
        # VLANs that will be configured on these ports.
        vlans: 11-12,21-22
        # Native VLAN to be used on these ports.
        native_vlan: 4092
        # L2 mode of the port.
        mode: trunk
        # Spanning tree portfast configuration on this port.
        spanning_tree_portfast: edge
        # Definition of the pair of ports as port channel.
        port_channel:
          # Description of the port channel interface.
          description: PortChannel dc1-leaf1-server1
          # Port channel mode for LACP.
          mode: active

      - endpoint_ports: [ iLO ]
        switch_ports: [ Ethernet5 ]
        switches: [ dc1-leaf1c ]
        vlans: 11
        mode: access
        spanning_tree_portfast: edge

  - name: dc1-leaf2-server1
    adapters:
      - endpoint_ports: [ PCI1, PCI2 ]
        switch_ports: [ Ethernet5, Ethernet5 ]
        switches: [ dc1-leaf2a, dc1-leaf2b ]
        vlans: 11-12,21-22
        native_vlan: 4092
        mode: trunk
        spanning_tree_portfast: edge
        port_channel:
          description: PortChannel dc1-leaf2-server1
          mode: active

      - endpoint_ports: [ iLO ]
        switch_ports: [ Ethernet5 ]
        switches: [ dc1-leaf2c ]
        vlans: 11
        mode: access
        spanning_tree_portfast: edge


  # Start of definitions for DC2 (identical to DC1)

  # Name of the defined server.
  - name: dc2-leaf1-server1
    # Definition of adapters on the server.
    adapters:
      # Name of the server interfaces that will be used in the description of each interface
      - endpoint_ports: [ PCI1, PCI2 ]
        # Device ports where the server ports are connected.
        switch_ports: [ Ethernet5, Ethernet5 ]
        # Device names where the server ports are connected.
        switches: [ dc2-leaf1a, dc2-leaf1b ]
        # VLANs that will be configured on these ports.
        vlans: 11-12,21-22
        # Native VLAN to be used on these ports.
        native_vlan: 4092
        # L2 mode of the port.
        mode: trunk
        # Spanning tree portfast configuration on this port.
        spanning_tree_portfast: edge
        # Definition of the pair of ports as port channel.
        port_channel:
          # Description of the port channel interface.
          description: PortChannel dc2-leaf1-server1
          # Port channel mode for LACP.
          mode: active

      - endpoint_ports: [ iLO ]
        switch_ports: [ Ethernet5 ]
        switches: [ dc2-leaf1c ]
        vlans: 11
        mode: access
        spanning_tree_portfast: edge

  - name: dc2-leaf2-server1
    adapters:
      - endpoint_ports: [ PCI1, PCI2 ]
        switch_ports: [ Ethernet5, Ethernet5 ]
        switches: [ dc2-leaf2a, dc2-leaf2b ]
        vlans: 11-12,21-22
        native_vlan: 4092
        mode: trunk
        spanning_tree_portfast: edge
        port_channel:
          description: PortChannel dc2-leaf2-server1
          mode: active

      - endpoint_ports: [ iLO ]
        switch_ports: [ Ethernet5 ]
        switches: [ dc2-leaf2c ]
        vlans: 11
        mode: access
        spanning_tree_portfast: edge

The configuration of the endpoints in DC2 is identical to the ones in DC1. The only change resides in the name of the leaves used and their ports.

The playbook

The playbook is also the same, as the actions to execute in the fabric are the same. It is important to validate the hosts variable in the playbook to include all Ansible groups.

Testing AVD output without a lab

Example of using this playbook without devices (local tasks):

---
# build.yml

- name: Build Configs
  hosts: FABRIC
  gather_facts: false
  tasks:

    - name: Generate AVD Structured Configurations and Fabric Documentation
      ansible.builtin.import_role:
        name: arista.avd.eos_designs

    - name: Generate Device Configurations and Documentation
      ansible.builtin.import_role:
        name: arista.avd.eos_cli_config_gen

Please look through the folders and files described above to learn more about the output generated by AVD.

Playbook Run

To build and deploy the configurations to your switches directly, using eAPI, run the playbook called deploy.yml. This assumes that your Ansible host has access and authentication rights to the switches. Those auth variables are defined in FABRIC.yml.

---
# deploy.yml

- name: Build and Deploy Configs
  hosts: FABRIC
  gather_facts: false
  tasks:

    - name: Generate AVD Structured Configurations and Fabric Documentation
      ansible.builtin.import_role:
        name: arista.avd.eos_designs

    - name: Generate Device Configurations and Documentation
      ansible.builtin.import_role:
        name: arista.avd.eos_cli_config_gen

    - name: Deploy Configurations to Devices
      ansible.builtin.import_role:
        name: arista.avd.eos_config_deploy_eapi
### Deploy Configurations to Devices using eAPI
ansible-playbook playbooks/deploy.yml

The execution of the playbook should produce the following output:

user@ubuntu:~/ansible-avd-examples/dual-dc-l3ls$ ansible-playbook build.yml

PLAY [Build Configs] ***************************************************************************************************************************************************************

TASK [arista.avd.eos_designs : Verify Requirements] ********************************************************************************************************************************
AVD version v4.0.0-rc1-8-ge1382fdb8
Use -v for details.
ok: [dc1-spine1 -> localhost]

TASK [arista.avd.eos_designs : Create required output directories if not present] **********************************************************************************************************
ok: [dc1-leaf1a -> localhost] => (item=/home/user/Documents/git_projects/ansible-avd-examples/dual-dc-l3ls/intended/structured_configs)
ok: [dc1-leaf1a -> localhost] => (item=/home/user/Documents/git_projects/ansible-avd-examples/dual-dc-l3ls/documentation/fabric)
(...)

If similar output is not shown, make sure:

  1. The documented requirements are met.
  2. The latest arista.avd collection is installed.

Troubleshooting

EVPN not working

If after doing the following steps:

  1. Manually copy/paste the switch-basic-configuration to the devices.
  2. Run the playbook and push the generated configuration to the fabric.
  3. Log in to a leaf device, for example, dc1-leaf1a, and run the show bgp evpn summary command to view EVPN routes.

The following error message is shown:

dc1-leaf1a#show bgp evpn summ
% Not supported
dc1-leaf1a#

This is caused by AVD pushing the configuration line service routing protocols model multi-agent, which enables the multi-agent routing process supporting EVPN. This change requires a reboot of the device.


Last update: August 17, 2023